TSTORE

Instruction Diagram

Introduction

Stores data in a tile to a GlobalTensor (GM), optionally using atomic write or quantization parameters.

Mathematical Semantics

The symbolic representation depends on the shape/stride of the GlobalTensor and the layout of the Tile. Conceptually (two-dimensional view, with base offset):

$$\mathrm{dst}_{r_0 + i,\; c_0 + j} = \mathrm{src}_{i,j}$$

Assembly Syntax

Synchronous form:

tstore %t1, %sv_out[%c0, %c0]

AS Level 1 (SSA)

pto.tstore %src, %mem : (!pto.tile<...>, !pto.partition_tensor_view<MxNxdtype>) -> ()

AS Level 2 (DPS)

pto.tstore ins(%src : !pto.tile_buf<...>) outs(%mem : !pto.partition_tensor_view<MxNxdtype>)

C++ Built-in APIs

Declared in include/pto/common/pto_instr.hpp and include/pto/common/constants.hpp:

The public include header is <pto/pto-inst.hpp>, and the internal declaration is located in pto/common/pto_instr.hpp.

template <typename TileData, typename GlobalData, AtomicType atomicType = AtomicType::AtomicNone,
          typename... WaitEvents>
PTO_INST RecordEvent TSTORE(GlobalData& dst, TileData& src, WaitEvents&... events);

template <typename TileData, typename GlobalData, AtomicType atomicType = AtomicType::AtomicNone,
          typename... WaitEvents>
PTO_INST RecordEvent TSTORE(GlobalData& dst, TileData& src, uint64_t preQuantScalar, WaitEvents&... events);

template <typename TileData, typename GlobalData, typename FpTileData, AtomicType atomicType = AtomicType::AtomicNone,
          typename... WaitEvents>
PTO_INST RecordEvent TSTORE_FP(GlobalData& dst, TileData& src, FpTileData& fp, WaitEvents&... events);

Constraints

• Implementation check (Atlas A2/A3 training products/Atlas A2/A3 inference products):
  • The source tile position must be one of the following: TileType::Vec, TileType::Mat, TileType::Acc.
  • Runtime: all dst.GetShape(dim) values and src.GetValidRow()/GetValidCol() must be > 0.
  • For source tile position TileType::Vec / TileType::Mat:
    • TileData::DType must be one of the following: int8_t, uint8_t, int16_t, uint16_t, int32_t, uint32_t, int64_t, uint64_t, half, bfloat16_t, float.
    • sizeof(TileData::DType) == sizeof(GlobalData::DType).
    • The layout must match ND/DN/NZ (or special case: TileData::Rows == 1 or TileData::Cols == 1).
    • For int64_t/uint64_t, only ND->ND or DN->DN is supported.
  • For the source tile position being TileType::Acc (including call forms with quantization parameters and atomic write variants):

    • The destination layout must be ND, NZ, NC1HWC0, or NDC1HWC0.

    • The source data type must be int32_t or float.

    • When quantization is not used, the destination data type must be int32_t/float/half/bfloat16_t.

    • The data type support for ACC-to-GM depends on the call form:

      Call Form	Source Data Type	Supported Target Data Types
      TSTORE(dst, acc)	float	float, half, bfloat16_t
      TSTORE(dst, acc)	int32_t	int32_t
      TSTORE(dst, acc, preQuantScalar) / TSTORE_FP(dst, acc, fp)	float	int8_t, uint8_t
      TSTORE(dst, acc, preQuantScalar) / TSTORE_FP(dst, acc, fp)	int32_t	int8_t, uint8_t, half

      Other cross-type combinations not listed are not within the supported scope.

    • Static shape constraints: 1 <= TileData::Cols <= 4095; if ND, 1 <= TileData::Rows <= 8192; if NZ, NC1HWC0, or NDC1HWC0, 1 <= TileData::Rows <= 65535 and TileData::Cols % 16 == 0.

    • Runtime: 1 <= src.GetValidCol() <= 4095.

• Implementation check (Ascend 950PR/Ascend 950DT):
  • The source tile position must be TileType::Vec or TileType::Acc (Mat storage is not supported on this target).
  • For source tile position TileType::Vec:
    • sizeof(TileData::DType) == sizeof(GlobalData::DType).
    • TileData::DType must be one of the following: int8_t, uint8_t, int16_t, uint16_t, int32_t, uint32_t, int64_t, uint64_t, half, bfloat16_t, float, float8_e4m3_t, float8_e5m2_t, hifloat8_t, float8_e8m0_t, float4_e1m2x2_t, float4_e2m1x2_t.
    • The layout must match ND/DN/NZ (or in special cases: TileData::Rows == 1 or TileData::Cols == 1).
    • Additional alignment constraints are enforced (for example, for ND, the row-major width in bytes must be a multiple of 32; for DN, the column-major height in bytes must be a multiple of 32, with exceptions in special cases).
  • For source tile position TileType::Acc (including call forms with quantization parameters and atomic write variants):

    • The target layout must be ND, NZ, NHWC, NCHW, or NCDHW; the source data type must be int32_t or float.

    • When quantization is not used, the target data type must be int32_t/float/half/bfloat16_t.

    • Data type support from ACC to GM depends on the call form:

      Call Form	Source Data Type	Supported Target Data Types
      TSTORE(dst, acc)	float	float, half, bfloat16_t
      TSTORE(dst, acc)	int32_t	int32_t
      TSTORE(dst, acc, preQuantScalar) / TSTORE_FP(dst, acc, fp)	float	int8_t, uint8_t, half, bfloat16_t, hifloat8_t, float8_e4m3_t, float
      TSTORE(dst, acc, preQuantScalar) / TSTORE_FP(dst, acc, fp)	int32_t	int8_t, uint8_t, half, bfloat16_t

      Other cross-type combinations not listed are not supported.

    • The static shape constraints are the same as the row/column constraints of Atlas A2/A3 training products/Atlas A2/A3 inference products; AtomicAdd additionally restricts the target data type to supported atomic types.

• Valid region:
  • The implementation uses src.GetValidRow()/src.GetValidCol() as the transfer size.

Examples

Automatic

#include <pto/pto-inst.hpp>

using namespace pto;

template <typename T>
void example_auto(__gm__ T* out) {
  using TileT = Tile<TileType::Vec, T, 16, 16>;
  using GShape = Shape<1, 1, 1, 16, 16>;
  using GStride = BaseShape2D<T, 16, 16, Layout::ND>;
  using GTensor = GlobalTensor<T, GShape, GStride, Layout::ND>;

  GTensor gout(out);
  TileT t;
  TSTORE(gout, t);
}

Manual

#include <pto/pto-inst.hpp>

using namespace pto;

template <typename T>
void example_manual(__gm__ T* out) {
  using TileT = Tile<TileType::Vec, T, 16, 16>;
  using GShape = Shape<1, 1, 1, 16, 16>;
  using GStride = BaseShape2D<T, 16, 16, Layout::ND>;
  using GTensor = GlobalTensor<T, GShape, GStride, Layout::ND>;

  GTensor gout(out);
  TileT t;
  TASSIGN(t, 0x1000);
  TSTORE<TileT, GTensor, AtomicType::AtomicAdd>(gout, t);
}

ASM Examples

Automatic Mode

# Automatic mode: the compiler/runtime is responsible for resource placement and scheduling.
pto.tstore %src, %mem : (!pto.tile<...>, !pto.partition_tensor_view<MxNxdtype>) -> ()

Manual Mode

# Manual mode: explicitly bind resources first, then issue the instruction.
# Optional (when the instruction contains tile operands):
# pto.tassign %arg0, @tile(0x1000)
# pto.tassign %arg1, @tile(0x2000)
pto.tstore %src, %mem : (!pto.tile<...>, !pto.partition_tensor_view<MxNxdtype>) -> ()

PTO Assembly Form

tstore %t1, %sv_out[%c0, %c0]
# AS Level 2 (DPS)
pto.tstore ins(%src : !pto.tile_buf<...>) outs(%mem : !pto.partition_tensor_view<MxNxdtype>)