LLM-DataDist Error Codes

Error codes are defined by the following macros:

namespace llm_datadist {
constexpr Status LLM_SUCCESS = 0x0U;
constexpr Status LLM_FAILED = 0xFFFFFFFFU;
constexpr Status LLM_WAIT_PROC_TIMEOUT = 0x5010B001U;
constexpr Status LLM_KV_CACHE_NOT_EXIST = 0x5010B002U;
constexpr Status LLM_PARAM_INVALID = 0x5010B005U;
constexpr Status LLM_NOT_YET_LINK = 0x5010B007U;
constexpr Status LLM_ALREADY_LINK = 0x5010B008U;
constexpr Status LLM_LINK_FAILED = 0x5010B009U;
constexpr Status LLM_UNLINK_FAILED = 0x5010B00AU;
constexpr Status LLM_NOTIFY_PROMPT_UNLINK_FAILED = 0x5010B00BU;
constexpr Status LLM_CLUSTER_NUM_EXCEED_LIMIT = 0x5010B00CU;
constexpr Status LLM_PROCESSING_LINK = 0x5010B00DU;
constexpr Status LLM_DEVICE_OUT_OF_MEMORY = 0x5010B00EU;
constexpr Status LLM_EXIST_LINK = 0x5010B018U;
constexpr Status LLM_FEATURE_NOT_ENABLED = 0x5010B019U;
constexpr Status LLM_TIMEOUT = 0x5010B01AU;
constexpr Status LLM_LINK_BUSY = 0x5010B01BU;
constexpr Status LLM_OUT_OF_MEMORY = 0x5010B01CU;
}  // namespace llm_datadist

The meanings of error codes are as follows.

Enumerated Value	Description	Recoverable (Yes/No)	Solution
LLM_SUCCESS	Success	None	None
LLM_FAILED	Common failure	No	Preserve the environment, collect host/device logs, and back them up.
LLM_WAIT_PROC_TIMEOUT	Processing timeout	Yes	If this error is reported by transmission-related APIs such as PullKvCache and PullKvBlocks, the link is unrecoverable and must be re-established. If this error is reported by other APIs, increase the timeout interval and try again.
LLM_KV_CACHE_NOT_EXIST	KV cache not found	Yes	Check whether the cache ID is correct. Check whether the cache has been released. Check whether the request in the full error log is complete. Check whether duplicate pull operations exist.
LLM_PARAM_INVALID	Incorrect parameter	Yes	Locate the fault based on logs.
LLM_NOT_YET_LINK	No link established	Yes	Verify the link status between the Decode and Prompt sides at the upper layer.
LLM_ALREADY_LINK	Link already established	Yes	Verify the link status between the Decode and Prompt sides at the upper layer.
LLM_LINK_FAILED	Link establishment failed	Yes	If this error code is returned in the second return value of LinkLlmClusters, check the network connection between the corresponding clusters.
LLM_UNLINK_FAILED	Link disconnection failed	Yes	If this error code is returned in the second return value of UnlinkLlmClusters, check the network connection between the corresponding clusters.
LLM_NOTIFY_PROMPT_UNLINK_FAILED	Failed to notify the Prompt side of link disconnection	Yes	Check the network connection between the Decode and Prompt. Call UnlinkLlmClusters on the Prompt side to clean up residual resources.
LLM_CLUSTER_NUM_EXCEED_LIMIT	Excessive clusters	Yes	Check the input parameters of LinkLlmClusters and UnlinkLlmClusters and ensure that the number of clusters must not exceed 16.
LLM_PROCESSING_LINK	Link establishment in progress	Yes	A link establishment or disconnection operation is in progress. Try again later.
LLM_DEVICE_OUT_OF_MEMORY	Insufficient device memory	Yes	Check whether the allocated memory is released.
LLM_EXIST_LINK	Unreleased links found during role setting	Yes	Before calling SetRole, ensure that all links are disconnected by calling UnlinkLlmClusters.
LLM_FEATURE_NOT_ENABLED	Feature not enabled	Yes	Check whether required parameters are passed in during LLM-DataDist initialization. Check whether unsupported APIs are called.
LLM_TIMEOUT	Processing timeout	No	Preserve the environment, collect host/device logs, and back them up.
LLM_LINK_BUSY	Link busy	Yes	Reserved error code, which is not returned currently.
LLM_OUT_OF_MEMORY	Insufficient memory	Yes	Check whether the memory pool or system memory is sufficient.

Parent topic: LLM-DataDist