昇腾论坛

请问EMMC可以使用和SD卡完全相同的方式制卡吗？

我是用了EMMC烧录器将EMMC连接到电脑，此时EMMC可以被当做U盘一样被检测到，然后采用python3 make_sd_card.py local /dev/sdb制卡，也显示了制卡成功。

现在启动过程中串口打印信息如下：

00000222

e005e006

pmu second pmu initial:0x3.

cur[2], last[0].

cur[3], last[0].

0.5

c-init ok

[NVE] xloader version:0x2220

cur[4], last[0].

▒Ձmode 3, efuse:264! enable 1!

cpu pll recfg function,success---242408!

cur[5], last[0].

cur[6], last[0].

cur[7], last[0].

current[2].

current[3].

uc sector[0] valid flag not enabled!

uc sector[1] valid flag not enabled!

[UC]ddr_iecc_en:0

current[21].

current[22].

current[23].

current[25].

current[26].

current[31].

freq 60 vol 2:

current[33].

Density:0x100010

Density:0xffffffff

Density:0x100010

Density:0xffffffff

Density:0x100010

Density:0xffffffff

Density:0x100010

Density:0xffffffff

Density:0x100010

Density:0xffffffff

Density:0x100010

Density:0xffffffff

Density:0x100010

Density:0xffffffff

Density:0x100010

Density:0xffffffff

ch_mask: 0xff

ch_lr: 0x3

ch_num: 0x8

rank_num: 0x1

Manufacturer ID[0]:0x13

Manufacturer ID[1]:0x13

Manufacturer ID[2]:0x13

Manufacturer ID[3]:0x13

Manufacturer ID[4]:0x13

Manufacturer ID[5]:0x13

Manufacturer ID[6]:0x13

Manufacturer ID[7]:0x13

Total size:0x8

DDR info:0x813

DDR_TYPE_8CH_ALL 1_rank 8G !

DDR HHA interleave enabled!

idx: 0 start_addr_l: 0x0 start_addr_h: 0x0 length: 0x800

idx: 1 start_addr_l: 0x80000000 start_addr_h: 0x8 length: 0x1800

current[34].

uce init entry

uce profile total is 0x32c

uce init end

current[35].

freq 400 vol 2:

freq 1600 vol 2:

HVrefThres:8

current[36].

uce init entry

uce profile total is 0x298

uce init end

current[40].

transfer ddr data to l2_buf 0x40000000.

current[51].

current[52].

current[54].

current[55].

current[52].

current[58].

current[59].

current[60].

current[62].

addr = d00c2030, value = 0

addr = d00c3580, value = 0

addr = d00c6320, value = 0

addr = b0070e00, value = 0

addr = d00c0a28, value = 0

addr = b0070e30, value = 0

addr = d00c0a58, value = 0

addr = b0070e18, value = 0

addr = d00c0a40, value = 0

addr = b0072000, value = 3

addr = d00c2540, value = 30

addr = d00c00a0, value = 3f

addr = d00c00a4, value = 3f

addr = d00c0030, value = 241f41

addr = d00c0034, value = 0

addr = d00c0038, value = 241f41

addr = d00c003c, value = 0

addr = d00c5000, value = 3f

addr = b0072004, value = 0

addr = d00c2550, value = 0

addr = d00c3690, value = 82

current[63].

DDR Total Capacity: 8192 MB.

DDR Rank Type: single.

DDR Channel with DRAM: A B C D E F G H

DDR Init 991 ms

current[65].

current[67].

cur[8], last[0].

maintain:0, static:0

cur[9], last[0].

[STID]adcin7:0x13.

[STID]adcin7_remap:0x0.

[STID]adcin8:0x13.

[STID]adcin8_remap:0x0.

cur[10], last[0].

SPI FLASH download uefi.

cur[25], last[0].

PCIE_RC_MODE...

g_imgNum = 1

cur[26], last[0].

SPI FLASH download uefi finish.

cur[34], last[0].

ns, suc

cur[35], last[0].

si suc

cur[36], last[0].

s vr bg

ns vr, sc

cur[37], last[0].

sv suc

high mntn_config=0xa0000000, low mntn_config=0x0

high addr=0x8, low addr=0x90000000

lpm3 will WFE

disreset A55.

cur[0], last[0].

aicore_power_on:312----core1 step1

aicore_pmu_up:233----repair step 5

_aicore0_buck_on:164---state -0x7--cfg:0x64--buck voltage:0x64

_aicore1_buck_on:222---state -0xf--cfg:0x64--buck voltage:0x64

_aimemory0_1_buck_on:193---state -0xf--cfg:0x64--buck voltage:0x64

aicore_pmu_up:257----pmu up step1

aicore0_power_reset:74

aicore0_power_reset:83

aicore1_power_reset:88

aicore1_power_reset:97

aicore1_isolation_enable:112----repair step 4

aicore_power_on:331----power on success.

DDR HHA interleave enabled!

NOTICE: Booting Trusted Firmware

NOTICE: BL1: Built :

NOTICE: BL1: Booting BL2

NOTICE: BL2: Built :

NOTICE: BL1: Booting BL31

NOTICE: BL31: Built :

booting cfg info 0x0, 0x0!

atl emmc: not install SDDriver

start boot linux.(4591)

booting cfg info 0x0, 0x0!