昇腾论坛

我们基于Atlas 200I A2加速模块的自研底板，在升级模式时上电后启动失败，eMMC初始化完好，但是SerDes 0被自动修改为了SATA

升级模式启动日志如下：

ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:10 adc0in1:589 adc0in2:92
adc1in2:93 adc1in3:587
adc boardId:51150
Load main hboot1_a
Load main hilink25
hboot1a hash a082466e.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01  02  05  06  11  15  21  65  28  95  198  11  00  128  209  137  96  117  49  220 
sfc set Qline.
SfcDevId: 1a67c8
Boot entry(119)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0900
boardid:51150
bootmode:4
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1

current[4], last[0]
[0.140] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
current[5], last[0]
[0.148] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|1|1]
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x7 0xf 0x3f
bitmap info update load success
SyscfgProc [347|1|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.177] [BOOT_TRACE]Load main lpddr
[0.211] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.226] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.248] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.289] [BOOT_TRACE]Load main hboot2
non-secure vef success!
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
Update ds[0] to sata mode
macro[0] protocols:
    ds[0] : SATA
    ds[1] : PCIE
    ds[2] : PCIE
    ds[3] : PCIE
macro[1] protocols:
    ds[0] : PCIE
    ds[1] : USB 
    ds[2] : USB 
    ds[3] : USB 
Macro[0] power up (time 438ms)
ERROR: Macro[0] Calibration failed
ERROR: Macro[0] macro init failed
current[12], last[0]
[0.211] [BOOT_TRACE] ddr init start
Dis all msd
swapType: 0x1
Zq cal start
Zq cal ok
C0 R2 S800 M1,R36666
C1 R2 S800 M1,R36666
C2 R2 S800 M1,R36666
C3 R2 S800 M1,R36666
C4 R2 S800 M1,R36666
C5 R2 S800 M1,R36666
ChMap: 0x3f
ddr freq: 2131
iecc disable
Rpt 0x3000, fb 0x800, msdw 0x3000
[0.709] [BOOT_TRACE] ddr init end
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[13], last[0]
[0.788] [BOOT_TRACE]finish image load.
current[28], last[0]
current[70], last[0]
[796.796]Dreset main core...
Jump to HSM...
NOTICE:  Mp conf...NOTICE:  ok
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: 
NOTICE:  BL1: Built : 
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: 
NOTICE:  BL2: Built : 
NOTICE:  BL1: Booting BL31
NOTICE:  BL31: 
NOTICE:  BL31: Built : 
NOTICE:  HSM boot keypoint 0x7807f!
NOTICE:  A55 wfi ...NOTICE:  OK
NOTICE:  A55 close
NOTICE:  jumper to uefi [898]
[  258][SetBootKeypoint] [0.970]------------------------------STAGE_UEFI_START
[  260][SetBootKeypoint] current keypoint[71], last keypoint[0].
[ 1028][PcieRcInitEntry] PcieMode=0
[  143][GetSerdesInfoFromSysCfgOrUserCfg] Pirnt UserSerdesInfo:
[  114][SerdesInfoPrint] Serdes info:
[  121][SerdesInfoPrint] serdes: 0 0 0 0 0 0 4 0 3 0
[  121][SerdesInfoPrint] serdes: 1 0 0 0 0 0 255 0 3 0
[  121][SerdesInfoPrint] serdes: 2 0 0 0 0 0 255 0 3 0
[  121][SerdesInfoPrint] serdes: 3 0 0 0 0 0 255 0 3 0
[  121][SerdesInfoPrint] serdes: 4 0 0 0 0 0 1 0 3 0
[  121][SerdesInfoPrint] serdes: 5 2 0 0 0 0 255 0 5 0
[  121][SerdesInfoPrint] serdes: 6 2 0 0 0 0 255 0 5 0
[  121][SerdesInfoPrint] serdes: 7 2 0 0 0 0 255 0 5 0

里面有报错打印：

Update ds[0] to sata mode

macro[0] protocols:

ds[0] : SATA

ds[1] : PCIE

ds[2] : PCIE

ds[3] : PCIE

macro[1] protocols:

ds[0] : PCIE

ds[1] : USB

ds[2] : USB

ds[3] : USB

Macro[0] power up (time 438ms)

ERROR: Macro[0] Calibration failed

ERROR: Macro[0] macro init failed

正常启动模式，由于eMMC还没有烧录系统，启动如下：

ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:11 adc0in1:589 adc0in2:92
adc1in2:92 adc1in3:589
adc boardId:51150
Load main hboot1_a
Load main hilink25
hboot1a hash a082466e.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01  02  05  06  11  15  21  65  28  95  198  11  00  128  209  137  96  117  49  220 
sfc set Qline.
SfcDevId: 1a67c8
Boot entry(119)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0900
boardid:51150
bootmode:4
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1

current[4], last[0]
[0.140] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
current[5], last[0]
[0.148] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|1|1]
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x7 0xf 0x3f
bitmap info update load success
SyscfgProc [347|1|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.176] [BOOT_TRACE]Load main lpddr
[0.211] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.226] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.248] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.289] [BOOT_TRACE]Load main hboot2
non-secure vef success!
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
Update ds[0] to sata mode
macro[0] protocols:
    ds[0] : SATA
    ds[1] : PCIE
    ds[2] : PCIE
    ds[3] : PCIE
macro[1] protocols:
    ds[0] : PCIE
    ds[1] : USB 
    ds[2] : USB 
    ds[3] : USB 
Macro[0] power up (time 438ms)
ERROR: Macro[0] Calibration failed
ERROR: Macro[0] macro init failed
current[12], last[0]
[0.211] [BOOT_TRACE] ddr init start
Dis all msd
swapType: 0x1
Zq cal start
Zq cal ok
C0 R2 S800 M1,R36666
C1 R2 S800 M1,R36666
C2 R2 S800 M1,R36666
C3 R2 S800 M1,R36666
C4 R2 S800 M1,R36666
C5 R2 S800 M1,R36666
ChMap: 0x3f
ddr freq: 2131
iecc disable
Rpt 0x3000, fb 0x800, msdw 0x3000
[0.704] [BOOT_TRACE] ddr init end
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[13], last[0]
[0.783] [BOOT_TRACE]finish image load.
current[28], last[0]
current[70], last[0]
[791.791]Dreset main core...
Jump to HSM...
NOTICE:  Mp conf...NOTICE:  ok
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: 
NOTICE:  BL1: Built : 
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: 
NOTICE:  BL2: Built : 
NOTICE:  BL1: Booting BL31
NOTICE:  BL31: 
NOTICE:  BL31: Built : 
NOTICE:  HSM boot keypoint 0x7807f!
NOTICE:  A55 wfi ...NOTICE:  OK
NOTICE:  A55 close
NOTICE:  jumper to uefi [893]
[  258][SetBootKeypoint] [0.965]------------------------------STAGE_UEFI_START
[  260][SetBootKeypoint] current keypoint[71], last keypoint[0].
[ 1028][PcieRcInitEntry] PcieMode=0
[  143][GetSerdesInfoFromSysCfgOrUserCfg] Pirnt UserSerdesInfo:
[  114][SerdesInfoPrint] Serdes info:
[  121][SerdesInfoPrint] serdes: 0 0 0 0 0 0 4 0 3 0
[  121][SerdesInfoPrint] serdes: 1 0 0 0 0 0 255 0 3 0
[  121][SerdesInfoPrint] serdes: 2 0 0 0 0 0 255 0 3 0
[  121][SerdesInfoPrint] serdes: 3 0 0 0 0 0 255 0 3 0
[  121][SerdesInfoPrint] serdes: 4 0 0 0 0 0 1 0 3 0
[  121][SerdesInfoPrint] serdes: 5 2 0 0 0 0 255 0 5 0
[  121][SerdesInfoPrint] serdes: 6 2 0 0 0 0 255 0 5 0
[  121][SerdesInfoPrint] serdes: 7 2 0 0 0 0 255 0 5 0
[ 1963][AutoBootLinux] auto boot.
[ 1968][AutoBootLinux] defined SLT N
[ 1974][AutoBootLinux] defined MDC N
[ 1980][AutoBootLinux] defined TEST N
[ 1986][AutoBootLinux] defined BIOS_GTEST N
[ 1992][AutoBootLinux] defined AS610 N
[ 2013][AutoBootLinux] This is eMMC boot entry
[ 1832][EmmcSdStartOs] emmcsd init
[ 2275][EmmcInitAct] SD/eMMC host init OK!
[ 2281][EmmcInitAct] EMMC_MODE
[ 1834][EmmcSdStartOs] emmcsd end
[  748][GetPartInfoHead] partition info head Magic = 0 invalid
[  748][GetPartInfoHead] partition info head Magic = 0 invalid
[  771][GetPartHeadEntry] get main and back partition info fail
[  791][GetPartitionInfo] get partition info or ctrl head fail, Status = Invalid Parameter
[ 2043][AutoBootLinux] Normal boot fail, Status = Invalid Parameter. start to b .

启动时SerDes 0也同样被自动修改为了SATA

关于昇腾

新闻与活动

交流与资讯

支持与服务

开源社区