设备启动的完整串口打印如下：
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:10 adc0in1:11 adc0in2:95
adc1in2:343 adc1in3:347
adc boardId:33100
Load main hboot1_a
Load main hilink25
hboot1a hash a082466e.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 137 96 117 49 220
sfc set Qline.
SfcDevId: 3a25c2
Qual mode [0x42424242]
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xc0940
boardid:33100
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.142] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.157] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
invalid strategy offset 17.
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|0]
write share info ok
The current node is invalid and cannot be written to the shared space.
The current node is invalid and cannot be written to the shared space.
write nosec share info ok
current[6], last[0]
[0.207] [BOOT_TRACE]Load main lpddr
[0.241] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.241] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.266] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.307] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting by boardid
invalid boardid(33100), use evb bom2 conf in default
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
Macro[0] power up (time 462ms)
Macro[1] power up (time 509ms)
[0.241] [BOOT_TRACE] ddr init start
Dis all msd
swapType: 0x1
Zq cal start
Zq cal ok
C0 R1 S400 M1,R36666
C1 R1 S400 M1,R36666
C4 R1 S400 M1,R36666
C5 R1 S400 M1,R36666
ChMap: 0x33
ddr freq: 1596
iecc disable
Rpt 0x1000, fb 0x400, msdw 0x1000
[0.526] [BOOT_TRACE] ddr init end
current[12], last[0]
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[13], last[0]
[0.635] [BOOT_TRACE]finish image load.
current[28], last[0]
current[70], last[0]
[643.643]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [750]
current keypoint[71], last keypoint[0].
current node id is BIOS_END_NODE_ID, 0x2
Get Ffnl Node Pos error, Status = 0xFFFFFFFF!
SerInfo is NULL, skip ConfigPcieCtrllerFromSysConfig!
[0.918] [BOOT_TRACE] auto boot.
This is sd boot entry
emmcsd init
Count(1)
end
current node id is BIOS_END_NODE_ID, 0x4
Get Ffnl Node Pos error, Status = FFFFFFFF!
RecEnable:0x0, GpioStatus:0x0
current keypoint[89], last keypoint[0].
start load os image
Boot2 flag:0x0, last Cnt:0x0, current Cnt:0x1.
Current start mode :0x0 not support.
boot: main.
[2.547] [BOOT_TRACE] load image success.
load crl from Storage media
current keypoint[90], last keypoint[0].
waiting for hsm ..OK
[2.573] [BOOT_TRACE] Tee Load Start.
NOTICE: pub crl does not exist, pub_crl_size = 0x0!
NOTICE: pub crl broken, update crl ok!
NOTICE: cms verify process success.
NOTICE: #TEE Start#
NOTICE: #TEE End#
NOTICE: hw_start_tee done!
[2.904] [BOOT_TRACE] Tee Load Done.
current keypoint[95], last keypoint[0].
2905 Image.
3016 Done.
3016 DTB.
3022 Done.
[/dev/mmcblk1p2]
SecId:80 0 81 4C
No dts found in DTB
====EqualVal[0]=====
Can't find dtb by boardId 0x814C in dt.img, use dtb.
SecId:80 0 81 4C
No dts found in DTB
====EqualVal[0]=====
Can't find dtb by boardId 0x814C in dt.img, use dtb.
IsColdBoot index|max[0|0] Status[0x1]
Reboot reason Str: reboot_reason=DEVICE_COLDBOOT.
Fdt delete sata Subnode
ras init done
jump kernel(3063).
current keypoint[99], last keypoint[0].
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x001fd022]
[ 0.000000] Linux version 5.10.0+ (phisik3@buildhost) (aarch64-target-linux-gnu-gcc (Do-Compiler V100R001C30B0032) 7.3.0, GNU ld (Do-Compiler V100R001C30B0032) 2.41) #1 SMP Tue Dec 31 00:00:00 CST 2024
[ 0.000000] Machine model: Hisilicon PhosphorHi1910B evb
[ 0.000000] earlycon: pl11 at MMIO32 0x00000000c4010000 (options '')
[ 0.000000] printk: bootconsole [pl11] enabled
NOTICE: mpidr on 100
NOTICE: mpidr on 200
NOTICE: mpidr on 300
[ 0.013075] KASLR disabled due to lack of seed
[ 0.115021] Initramfs unpacking failed: invalid magic at start of compressed archive
[ 0.280670] pinctrl-single 82320000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.289298] pinctrl-single c4000000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.297894] pinctrl-single 400140000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.306477] pinctrl-single 3001d0000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.325758] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.350981] mpam_device: Not support to register irq 0
[ 0.356117] mpam_device: Not support to register irq 0
Welcome to openEuler 22.03 LTS dracut-055-4.oe2203 (Initramfs)!
[ OK ] Created slice Slice /system/getty.
[ OK ] Created slice Slice /system/modprobe.
[ OK ] Created slice Slice /system/serial-getty.
[ OK ] Created slice Slice /system/sshd-keygen.
[ OK ] Created slice User and Session Slice.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ OK ] Set up automount Arbitrary…s File System Automount Point.
[ OK ] Reached target Path Units.
[ OK ] Reached target Slice Units.
[ OK ] Reached target Swaps.
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Reached target RPC Port Mapper.
[ OK ] Listening on Process Core Dump Socket.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on udev Kernel Socket.
Mounting Huge Pages File System...
Mounting POSIX Message Queue File System...
Mounting Kernel Debug File System...
Mounting Kernel Trace File System...
Mounting Temporary Directory /tmp...
Starting Create List of Static Device Nodes...
Starting Load Kernel Module configfs...
Starting Load Kernel Module drm...
Starting Load Kernel Module fuse...
Starting Journal Service...
Starting Load Kernel Modules...
Starting Remount Root and Kernel File Systems...
Starting Coldplug All udev Devices...
[ OK ] Started Journal Service.
[ OK ] Mounted Huge Pages File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Trace File System.
[ OK ] Mounted Temporary Directory /tmp.
[ OK ] Finished Create List of Static Device Nodes.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module fuse.
[ OK ] Finished Remount Root and Kernel File Systems.
Mounting FUSE Control File System...
Mounting Kernel Configuration File System...
Starting Create Static Device Nodes in /dev...
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Finished Coldplug All udev Devices.
[ OK ] Reached target Preparation for Local File Systems.
Mounting /var/log...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Mounted /var/log.
[ OK ] Started Rule-based Manager for Device Events and Files.
[ OK ] Found device /dev/ttyAMA0.
[ OK ] Found device /dev/mmcblk1p4.
Mounting /home/data...
[ OK ] Found device /dev/mmcblk1p7.
Mounting /home/package...
[ OK ] Found device /dev/mmcblk1p5.
Mounting /home/log...
[ OK ] Found device /dev/mmcblk1p6.
Mounting /usr/local/mindx...
[ OK ] Mounted /home/package.
[ OK ] Mounted /usr/local/mindx.
[ OK ] Mounted /home/log.
[ OK ] Mounted /home/data.
Starting etc file resume...
[ OK ] Finished Load Kernel Modules.
Starting Apply Kernel Variables...
[ OK ] Finished Apply Kernel Variables.
[ OK ] Started etc file resume.
[ OK ] Reached target Local File Systems.
Starting Restore /run/initramfs on shutdown...
Starting start davinci Service...
Starting Create Volatile Files and Directories...
[ OK ] Finished Restore /run/initramfs on shutdown.
[ OK ] Finished Create Volatile Files and Directories.
Mounting RPC Pipe File System...
Starting RPC Bind...
Starting Record System Boot/Shutdown in UTMP...
[ OK ] Mounted RPC Pipe File System.
[ OK ] Reached target rpc_pipefs.target.
[ OK ] Finished Record System Boot/Shutdown in UTMP.
[ OK ] Reached target System Initialization.
[ OK ] Started dnf makecache --timer.
[ OK ] Started Run system activit…ounting tool every 10 minutes.
[ OK ] Started Generate summary o…esterday's process accounting.
[ OK ] Reached target Timer Units.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Socket Units.
[ OK ] Reached target Basic System.
Starting D-Bus System Message Bus...
Starting Update RTC With System Clock...
Starting Hardware Monitoring Sensors...
Starting Self Monitoring a…g Technology (SMART) Daemon...
[ OK ] Reached target sshd-keygen.target.
Starting Resets System Activity Logs...
Starting User Login Management...
[ OK ] Started RPC Bind.
[ OK ] Finished Update RTC With System Clock.
[FAILED] Failed to start Hardware Monitoring Sensors.
See 'systemctl status lm_sensors.service' for details.
[ OK ] Finished Resets System Activity Logs.
[ OK ] Started Self Monitoring an…ing Technology (SMART) Daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Network Manager...
[ OK ] Started User Login Management.
[ OK ] Started Network Manager.
[ OK ] Reached target Network.
Starting Network Manager Wait Online...
Starting GSSAPI Proxy Daemon...
Starting /etc/rc.d/rc.local Compatibility...
Starting OpenSSH server daemon...
[ OK ] Started /etc/rc.d/rc.local Compatibility.
Starting Hostname Service...
[ OK ] Started OpenSSH server daemon.
[ OK ] Started Hostname Service.
[ OK ] Created slice Slice /system/systemd-coredump.
[ OK ] Started Process Core Dump (PID 1514/UID 0).
[ OK ] Started GSSAPI Proxy Daemon.
[ OK ] Reached target NFS client services.
[ OK ] Reached target Preparation for Remote File Systems.
[ OK ] Reached target Remote File Systems.
Starting Permit User Sessions...
[ OK ] Finished Permit User Sessions.
[ OK ] Started Command Scheduler.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyAMA0.
[ OK ] Reached target Login Prompts.
Starting Network Manager Script Dispatcher Service...
[ OK ] Started Network Manager Script Dispatcher Service.
[ OK ] Finished Network Manager Wait Online.
[ OK ] Reached target Network is Online.
Starting Notify NFS peers of a restart...
Starting System Logging Service...
[ OK ] Started Notify NFS peers of a restart.
[ OK ] Started System Logging Service.
NOTICE: Int ID:174, syscnt:0x2396be7d
NOTICE: intNum 174, nodeStatus1 0x40 !
NOTICE: [RasCbbCommonHandler]:[71L] moduleBase c1260000
NOTICE: [RasCbbCommonHandler]:[81] UE
NOTICE: [Module] MATA0
NOTICE: [FillHisiModuleErrorInfo]:[275L] moduleID = 0x14
NOTICE: [Module] MATA0
NOTICE: SubSysID:0xff, DeviceID:0x0, SubSysNum:0x0
NOTICE: RECOVERABLE!
NOTICE: HestNotifiedOS
NOTICE: [RasCbbCommonHandler]:[89] Handler end
NOTICE: base = 0xc1260000
NOTICE: ERR_FRL = 0x142aa2
NOTICE: ERR_FRH = 0x0
NOTICE: ERR_CTRLL = 0x515
NOTICE: ERR_CTRLH = 0x0
NOTICE: ERR_STATUSL = 0xfc30050e
NOTICE: ERR_STATUSH = 0x0
NOTICE: ERR_ADDRL = 0x10080010
NOTICE: ERR_ADDRH = 0xe0000001
NOTICE: ERR_MISC0L = 0x0
NOTICE: ERR_MISC0H = 0x0
NOTICE: ERR_MISC1L = 0xd798005
NOTICE: ERR_MISC1H = 0x800122
NOTICE: el3_int exit!
cpu 0 entering scheduler
>>>>>>>>>>>>LiteOS start succeed!<<<<<<<<<<<
Starting Hostname Service...
[ OK ] Started Hostname Service.
[16.033777s][BOOT_TRACE][PM]pm=0x0
[16.065782s][BOOT_TRACE][PM]pm=0x20000001
NOTICE: domain_off
NOTICE: socket 0 cluster 0 core 1
NOTICE: domain_off
NOTICE: socket 0 cluster 0 core 2
NOTICE: domain_off
NOTICE: socket 0 cluster 0 core 3
NOTICE: power_state 1010000
NOTICE: Go to suspend
NOTICE: gic cpuif disable
NOTICE: gic save
NOTICE: Gicd closed OK
NOTICE: socket 0 cluster 0 core 0
NOTICE: suspend end
启动到NOTICE: suspend end的时候，就一直卡主，硬重启也不生效，请帮忙分析下原因？
点赞
收藏
回复
分享
举报
已解决
设备启动的完整串口打印如下：
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:10 adc0in1:11 adc0in2:95
adc1in2:343 adc1in3:347
adc boardId:33100
Load main hboot1_a
Load main hilink25
hboot1a hash a082466e.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 137 96 117 49 220
sfc set Qline.
SfcDevId: 3a25c2
Qual mode [0x42424242]
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xc0940
boardid:33100
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.142] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.157] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
invalid strategy offset 17.
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|0]
write share info ok
The current node is invalid and cannot be written to the shared space.
The current node is invalid and cannot be written to the shared space.
write nosec share info ok
current[6], last[0]
[0.207] [BOOT_TRACE]Load main lpddr
[0.241] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.241] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.266] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.307] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting by boardid
invalid boardid(33100), use evb bom2 conf in default
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
Macro[0] power up (time 462ms)
Macro[1] power up (time 509ms)
[0.241] [BOOT_TRACE] ddr init start
Dis all msd
swapType: 0x1
Zq cal start
Zq cal ok
C0 R1 S400 M1,R36666
C1 R1 S400 M1,R36666
C4 R1 S400 M1,R36666
C5 R1 S400 M1,R36666
ChMap: 0x33
ddr freq: 1596
iecc disable
Rpt 0x1000, fb 0x400, msdw 0x1000
[0.526] [BOOT_TRACE] ddr init end
current[12], last[0]
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[13], last[0]
[0.635] [BOOT_TRACE]finish image load.
current[28], last[0]
current[70], last[0]
[643.643]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [750]
current keypoint[71], last keypoint[0].
current node id is BIOS_END_NODE_ID, 0x2
Get Ffnl Node Pos error, Status = 0xFFFFFFFF!
SerInfo is NULL, skip ConfigPcieCtrllerFromSysConfig!
[0.918] [BOOT_TRACE] auto boot.
This is sd boot entry
emmcsd init
Count(1)
end
current node id is BIOS_END_NODE_ID, 0x4
Get Ffnl Node Pos error, Status = FFFFFFFF!
RecEnable:0x0, GpioStatus:0x0
current keypoint[89], last keypoint[0].
start load os image
Boot2 flag:0x0, last Cnt:0x0, current Cnt:0x1.
Current start mode :0x0 not support.
boot: main.
[2.547] [BOOT_TRACE] load image success.
load crl from Storage media
current keypoint[90], last keypoint[0].
waiting for hsm ..OK
[2.573] [BOOT_TRACE] Tee Load Start.
NOTICE: pub crl does not exist, pub_crl_size = 0x0!
NOTICE: pub crl broken, update crl ok!
NOTICE: cms verify process success.
NOTICE: #TEE Start#
NOTICE: #TEE End#
NOTICE: hw_start_tee done!
[2.904] [BOOT_TRACE] Tee Load Done.
current keypoint[95], last keypoint[0].
2905 Image.
3016 Done.
3016 DTB.
3022 Done.
[/dev/mmcblk1p2]
SecId:80 0 81 4C
No dts found in DTB
====EqualVal[0]=====
Can't find dtb by boardId 0x814C in dt.img, use dtb.
SecId:80 0 81 4C
No dts found in DTB
====EqualVal[0]=====
Can't find dtb by boardId 0x814C in dt.img, use dtb.
IsColdBoot index|max[0|0] Status[0x1]
Reboot reason Str: reboot_reason=DEVICE_COLDBOOT.
Fdt delete sata Subnode
ras init done
jump kernel(3063).
current keypoint[99], last keypoint[0].
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x001fd022]
[ 0.000000] Linux version 5.10.0+ (phisik3@buildhost) (aarch64-target-linux-gnu-gcc (Do-Compiler V100R001C30B0032) 7.3.0, GNU ld (Do-Compiler V100R001C30B0032) 2.41) #1 SMP Tue Dec 31 00:00:00 CST 2024
[ 0.000000] Machine model: Hisilicon PhosphorHi1910B evb
[ 0.000000] earlycon: pl11 at MMIO32 0x00000000c4010000 (options '')
[ 0.000000] printk: bootconsole [pl11] enabled
NOTICE: mpidr on 100
NOTICE: mpidr on 200
NOTICE: mpidr on 300
[ 0.013075] KASLR disabled due to lack of seed
[ 0.115021] Initramfs unpacking failed: invalid magic at start of compressed archive
[ 0.280670] pinctrl-single 82320000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.289298] pinctrl-single c4000000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.297894] pinctrl-single 400140000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.306477] pinctrl-single 3001d0000.pinmux: please update dts to use #pinctrl-cells = <1>
[ 0.325758] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.350981] mpam_device: Not support to register irq 0
[ 0.356117] mpam_device: Not support to register irq 0
Welcome to openEuler 22.03 LTS dracut-055-4.oe2203 (Initramfs)!
[ OK ] Created slice Slice /system/getty.
[ OK ] Created slice Slice /system/modprobe.
[ OK ] Created slice Slice /system/serial-getty.
[ OK ] Created slice Slice /system/sshd-keygen.
[ OK ] Created slice User and Session Slice.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ OK ] Set up automount Arbitrary…s File System Automount Point.
[ OK ] Reached target Path Units.
[ OK ] Reached target Slice Units.
[ OK ] Reached target Swaps.
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Reached target RPC Port Mapper.
[ OK ] Listening on Process Core Dump Socket.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on udev Kernel Socket.
Mounting Huge Pages File System...
Mounting POSIX Message Queue File System...
Mounting Kernel Debug File System...
Mounting Kernel Trace File System...
Mounting Temporary Directory /tmp...
Starting Create List of Static Device Nodes...
Starting Load Kernel Module configfs...
Starting Load Kernel Module drm...
Starting Load Kernel Module fuse...
Starting Journal Service...
Starting Load Kernel Modules...
Starting Remount Root and Kernel File Systems...
Starting Coldplug All udev Devices...
[ OK ] Started Journal Service.
[ OK ] Mounted Huge Pages File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Trace File System.
[ OK ] Mounted Temporary Directory /tmp.
[ OK ] Finished Create List of Static Device Nodes.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module fuse.
[ OK ] Finished Remount Root and Kernel File Systems.
Mounting FUSE Control File System...
Mounting Kernel Configuration File System...
Starting Create Static Device Nodes in /dev...
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Finished Coldplug All udev Devices.
[ OK ] Reached target Preparation for Local File Systems.
Mounting /var/log...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Mounted /var/log.
[ OK ] Started Rule-based Manager for Device Events and Files.
[ OK ] Found device /dev/ttyAMA0.
[ OK ] Found device /dev/mmcblk1p4.
Mounting /home/data...
[ OK ] Found device /dev/mmcblk1p7.
Mounting /home/package...
[ OK ] Found device /dev/mmcblk1p5.
Mounting /home/log...
[ OK ] Found device /dev/mmcblk1p6.
Mounting /usr/local/mindx...
[ OK ] Mounted /home/package.
[ OK ] Mounted /usr/local/mindx.
[ OK ] Mounted /home/log.
[ OK ] Mounted /home/data.
Starting etc file resume...
[ OK ] Finished Load Kernel Modules.
Starting Apply Kernel Variables...
[ OK ] Finished Apply Kernel Variables.
[ OK ] Started etc file resume.
[ OK ] Reached target Local File Systems.
Starting Restore /run/initramfs on shutdown...
Starting start davinci Service...
Starting Create Volatile Files and Directories...
[ OK ] Finished Restore /run/initramfs on shutdown.
[ OK ] Finished Create Volatile Files and Directories.
Mounting RPC Pipe File System...
Starting RPC Bind...
Starting Record System Boot/Shutdown in UTMP...
[ OK ] Mounted RPC Pipe File System.
[ OK ] Reached target rpc_pipefs.target.
[ OK ] Finished Record System Boot/Shutdown in UTMP.
[ OK ] Reached target System Initialization.
[ OK ] Started dnf makecache --timer.
[ OK ] Started Run system activit…ounting tool every 10 minutes.
[ OK ] Started Generate summary o…esterday's process accounting.
[ OK ] Reached target Timer Units.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Socket Units.
[ OK ] Reached target Basic System.
Starting D-Bus System Message Bus...
Starting Update RTC With System Clock...
Starting Hardware Monitoring Sensors...
Starting Self Monitoring a…g Technology (SMART) Daemon...
[ OK ] Reached target sshd-keygen.target.
Starting Resets System Activity Logs...
Starting User Login Management...
[ OK ] Started RPC Bind.
[ OK ] Finished Update RTC With System Clock.
[FAILED] Failed to start Hardware Monitoring Sensors.
See 'systemctl status lm_sensors.service' for details.
[ OK ] Finished Resets System Activity Logs.
[ OK ] Started Self Monitoring an…ing Technology (SMART) Daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Network Manager...
[ OK ] Started User Login Management.
[ OK ] Started Network Manager.
[ OK ] Reached target Network.
Starting Network Manager Wait Online...
Starting GSSAPI Proxy Daemon...
Starting /etc/rc.d/rc.local Compatibility...
Starting OpenSSH server daemon...
[ OK ] Started /etc/rc.d/rc.local Compatibility.
Starting Hostname Service...
[ OK ] Started OpenSSH server daemon.
[ OK ] Started Hostname Service.
[ OK ] Created slice Slice /system/systemd-coredump.
[ OK ] Started Process Core Dump (PID 1514/UID 0).
[ OK ] Started GSSAPI Proxy Daemon.
[ OK ] Reached target NFS client services.
[ OK ] Reached target Preparation for Remote File Systems.
[ OK ] Reached target Remote File Systems.
Starting Permit User Sessions...
[ OK ] Finished Permit User Sessions.
[ OK ] Started Command Scheduler.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyAMA0.
[ OK ] Reached target Login Prompts.
Starting Network Manager Script Dispatcher Service...
[ OK ] Started Network Manager Script Dispatcher Service.
[ OK ] Finished Network Manager Wait Online.
[ OK ] Reached target Network is Online.
Starting Notify NFS peers of a restart...
Starting System Logging Service...
[ OK ] Started Notify NFS peers of a restart.
[ OK ] Started System Logging Service.
NOTICE: Int ID:174, syscnt:0x2396be7d
NOTICE: intNum 174, nodeStatus1 0x40 !
NOTICE: [RasCbbCommonHandler]:[71L] moduleBase c1260000
NOTICE: [RasCbbCommonHandler]:[81] UE
NOTICE: [Module] MATA0
NOTICE: [FillHisiModuleErrorInfo]:[275L] moduleID = 0x14
NOTICE: [Module] MATA0
NOTICE: SubSysID:0xff, DeviceID:0x0, SubSysNum:0x0
NOTICE: RECOVERABLE!
NOTICE: HestNotifiedOS
NOTICE: [RasCbbCommonHandler]:[89] Handler end
NOTICE: base = 0xc1260000
NOTICE: ERR_FRL = 0x142aa2
NOTICE: ERR_FRH = 0x0
NOTICE: ERR_CTRLL = 0x515
NOTICE: ERR_CTRLH = 0x0
NOTICE: ERR_STATUSL = 0xfc30050e
NOTICE: ERR_STATUSH = 0x0
NOTICE: ERR_ADDRL = 0x10080010
NOTICE: ERR_ADDRH = 0xe0000001
NOTICE: ERR_MISC0L = 0x0
NOTICE: ERR_MISC0H = 0x0
NOTICE: ERR_MISC1L = 0xd798005
NOTICE: ERR_MISC1H = 0x800122
NOTICE: el3_int exit!
cpu 0 entering scheduler
>>>>>>>>>>>>LiteOS start succeed!<<<<<<<<<<<
Starting Hostname Service...
[ OK ] Started Hostname Service.
[16.033777s][BOOT_TRACE][PM]pm=0x0
[16.065782s][BOOT_TRACE][PM]pm=0x20000001
NOTICE: domain_off
NOTICE: socket 0 cluster 0 core 1
NOTICE: domain_off
NOTICE: socket 0 cluster 0 core 2
NOTICE: domain_off
NOTICE: socket 0 cluster 0 core 3
NOTICE: power_state 1010000
NOTICE: Go to suspend
NOTICE: gic cpuif disable
NOTICE: gic save
NOTICE: Gicd closed OK
NOTICE: socket 0 cluster 0 core 0
NOTICE: suspend end
启动到NOTICE: suspend end的时候，就一直卡主，硬重启也不生效，请帮忙分析下原因？