ep/rc mode: 0 

Enable wdg. 

#1 

Pll Init ..pll[0] inited 

pll[2] inited 

pll[3] inited 

pll[4] inited 

pll[5] inited 

OK. 

reset src:0x0000000e 

lsadc dreset ok 

lsadc0 init ok 

adc0in0:11 adc0in1:588 adc0in2:94 

adc1in2:93 adc1in3:616 

adc boardId:51150 

Load main hboot1_a 

Load main hilink25 

hboot1a hash 03f0ed1c. 

Boot Entry. 

Load main hboot1_b 

[0.091] [BOOT_TRACE]1b start 

current[3], last[0] 

Dfx init l2 xloader done 

Hboot1_a point:[06] 01  02  05  06  11  15  21  65  28  95  198  11  00  128  209  137  96  117  49  220  

sfc set Qline. 

Device id: 0x3a25c2 

Qual mode [0x42] 

Quad Enable:0x44ee44ee 

Boot entry(123) 

Iso state: 0x0 

pll[6] inited 

pll[7] inited 

pll[8] inited 

pll[9] inited 

pll[10] inited 

 

Board info: 

sctrl pad info  : 0xc0900 

boardid         : 51150 

bootmode        : 4 

ep/rc mode      : 0 

pg info         : 0 

reset reason    : 0xe 

sfc mode        : 4byte 

secure boot     : 1 

 

current[4], last[0] 

[0.151] [BOOT_TRACE]Load main userbasecfg 

non-secure vef success! 

Cfg type-1 no cfg info. 

No info in userBaseConfig 

current[5], last[0] 

[0.164] [BOOT_TRACE]Load main sysbasecfg 

SyscfgProc [350|0|1] 

Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x7 0xf 0x3f 

bitmap info update load success 

SyscfgProc [352|0|1] 

write share info ok 

write nosec share info ok 

current[6], last[0] 

[0.192] [BOOT_TRACE]Load main lpddr 

[0.226] [BOOT_TRACE]Dreset Ts OK 

current[7], last[0] 

[0.241] [BOOT_TRACE]Load main hsmtag 

done. 

current[8], last[0] 

[0.264] [BOOT_TRACE]Load main atf 

report atf info to ddr OK 

current[9], last[0] 

[0.305] [BOOT_TRACE]Load main hboot2 

report uefi info to ddr OK 

PCIE0/1/2/3 RC Config Preset OK. 

use macro setting from syscfg 

macro[0] protocols: 

    ds[0] : PCIE 

    ds[1] : PCIE 

    ds[2] : PCIE 

    ds[3] : PCIE 

macro[1] protocols: 

    ds[0] : PCIE 

    ds[1] : USB  

    ds[2] : USB  

    ds[3] : USB  

Macro[0] power up (time 454ms) 

ERROR: Macro[0] Calibration failed 

ERROR: Macro[0] macro init failed 

[0.226] [BOOT_TRACE] ddr init start 

swapType: 0x1 

Zq cal start 

Zq cal ok 

C0 R2 S800 M1,R36666 

C1 R2 S800 M1,R36666 

C2 R2 S800 M1,R36666 

C3 R2 S800 M1,R36666 

C4 R2 S800 M1,R36666 

C5 R2 S800 M1,R36666 

ChMap: 0x3f 

ddr freq: 2131 

iecc disable 

Rpt 0x3000, fb 0x800, msdw 0x3000 

[0.731] [BOOT_TRACE] ddr init end 

Dfx init ddr done 

Init bbox data region 

Copy cfg OK. 

Copy cfg OK. 

Copy ddr Cache done. 

current[10], last[0] 

[0.810] [BOOT_TRACE]finish image load. 

current[20]mp to HSM... 

NOTICE:  Mp conf...NOTICE:  ok 

NOTICE:  Booting Trusted Firmware 

NOTICE:  BL1:  

NOTICE:  BL1: Built :  

NOTICE:  BL1: Booting BL2 

NOTICE:  BL2:  

NOTICE:  BL2: Built :  

NOTINOTICE:  BL31:  

NOTICE:  BL31: Built :  

NOTICE:  HSM boot keypoint 0x7807d! 

NOTICE:  A55 wfi ...NOTICE:  OK 

NOTICE:  A55 close 

NOTICE:  jumper to uefi [898] 

current keypoint[71], last keypoint[0].