新的200DK A2 开发板 20T算力版本，使用制卡工具制作，sd卡为128G 金士顿 ，启动后报
ERROR: image size check fail!
ERROR: size check failed!
ERROR: tee check before verity fail!
ERROR: tee decrypt or cms verify failed.
Image Auth Fail, 0xFFFFFFFF!
使用以前能启动的卡
以下为串口启动报文。
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:12 adc0in1:586 adc0in2:93
adc1in2:91 adc1in3:588
adc boardId:51150
Load main hboot1_a
Load main hilink25
hboot1a hash b25711e0.
Boot Entry.
Load main hboot1_b
[0.091] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 137 96 117 49 220
sfc set Qline.
Device id: 0x3a25c2
Qual mode status:[0x42]
Quad Enable:0x44ee44ee
Boot entry(123)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info : 0xd0940
boardid : 51150
bootmode : 5
ep/rc mode : 0
pg info : 0
reset reason : 0x1
sfc mode : 4byte
secure boot : 1
current[4], last[0]
[0.152] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.164] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [350|0|1]
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x7 0xf 0x3f
bitmap info update load success
SyscfgProc [352|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.192] [BOOT_TRACE]Load main lpddr
[0.226] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.226] [BOOT_TRACE]Load main hsmtag
done.
current[8], last[0]
[0.251] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.292] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : PCIE
ds[1] : USB
ds[2] : USB
ds[3] : USB
Macro[0] power up (time 442ms)
Macro[1] power up (time 488ms)
[0.226] [BOOT_TRACE] ddr init start
swapType: 0x1
Zq cal start
Zq cal ok
C0 R2 S800 M1,R36666
C1 R2 S800 M1,R36666
C2 R2 S800 M1,R36666
C3 R2 S800 M1,R36666
C4 R2 S800 M1,R36666
C5 R2 S800 M1,R36666
ChMap: 0x3f
ddr freq: 2131
iecc disable
Rpt 0x3000, fb 0x800, msdw 0x3000
[0.752] [BOOT_TRACE] ddr init end
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.832] [BOOT_TRACE]finish image load.
current[20]p to HSM...
NOTICE: socket 0 mp config
NOTICE: Gicd, its and mbigen dreset ok
NOTICE: Sata dreset ok
NOTICE: Aic dreset ok, state 0x0
NOTICE: Peri sub mbigen init ok
NOTICE: L3D sec space cfg...NOTICE: ok
NOTICE: L3t lp icg module en cfg...NOTICE: ok
NOTICE: MN init(ASIC/EMU) start
NOTICE: MN barrier 0x35b, dvm 0x31b
NOTICE: MN init ok
NOTICE: NIC/SATA/USB SMMU bypass ok
NOTICE: Smmu init(ASIC/EMU) ok
NOTICE: L2buf secure init ok
NOTICE: ErrRsp Config(ASIC/EMU) ok
NOTICE: switch 1.8V voltage for sd is ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTINOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: mApeiTrustfirmwareStruc = 0x10602000
NOTICE: BL3-1: clean atf dcache
NOTICE: BL3-1: jump to prepi entry
current keypoint[71], last keypoint[0].
[1.107] [BOOT_TRACE] auto boot.
This is sd boot entry
emmcsd init
count(1)
end
SYS Enable:0x0, gpio:0x5
recEnable:0x0, gpioStatus:0x0
current keypoint[89], last keypoint[0].
start load os image
try flag:0x0, reset count:0x0
cpld val: 0x0.
boot2 reset count:0x1
Current start mode :0x0 not support.
boot area main.
1301 imgS.
5173 imgE.
[5.305] [BOOT_TRACE] load image success.
load crl from Storage media
current keypoint[90], last keypoint[0].
waiting for hsm ready..OK
[5.334] [BOOT_TRACE] Tee Load Start.
ERROR: image size check fail!
ERROR: size check failed!
ERROR: tee check before verity fail!
ERROR: tee decrypt or cms verify failed.
Image Auth Fail, 0xFFFFFFFF!
TEE Verify Fail, Size = 0x500000, status = 0xFFFFFFFF!
TEE Load Failed, Status = Security Violation!
Normal boot fail, Status = Security Violation. start to b .
点赞
收藏
回复
分享
举报
已解决
新的200DK A2 开发板 20T算力版本，使用制卡工具制作，sd卡为128G 金士顿 ，启动后报
ERROR: image size check fail!
ERROR: size check failed!
ERROR: tee check before verity fail!
ERROR: tee decrypt or cms verify failed.
Image Auth Fail, 0xFFFFFFFF!
使用以前能启动的卡
以下为串口启动报文。
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:12 adc0in1:586 adc0in2:93
adc1in2:91 adc1in3:588
adc boardId:51150
Load main hboot1_a
Load main hilink25
hboot1a hash b25711e0.
Boot Entry.
Load main hboot1_b
[0.091] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 137 96 117 49 220
sfc set Qline.
Device id: 0x3a25c2
Qual mode status:[0x42]
Quad Enable:0x44ee44ee
Boot entry(123)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info : 0xd0940
boardid : 51150
bootmode : 5
ep/rc mode : 0
pg info : 0
reset reason : 0x1
sfc mode : 4byte
secure boot : 1
current[4], last[0]
[0.152] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.164] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [350|0|1]
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x7 0xf 0x3f
bitmap info update load success
SyscfgProc [352|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.192] [BOOT_TRACE]Load main lpddr
[0.226] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.226] [BOOT_TRACE]Load main hsmtag
done.
current[8], last[0]
[0.251] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.292] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : PCIE
ds[1] : USB
ds[2] : USB
ds[3] : USB
Macro[0] power up (time 442ms)
Macro[1] power up (time 488ms)
[0.226] [BOOT_TRACE] ddr init start
swapType: 0x1
Zq cal start
Zq cal ok
C0 R2 S800 M1,R36666
C1 R2 S800 M1,R36666
C2 R2 S800 M1,R36666
C3 R2 S800 M1,R36666
C4 R2 S800 M1,R36666
C5 R2 S800 M1,R36666
ChMap: 0x3f
ddr freq: 2131
iecc disable
Rpt 0x3000, fb 0x800, msdw 0x3000
[0.752] [BOOT_TRACE] ddr init end
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.832] [BOOT_TRACE]finish image load.
current[20]p to HSM...
NOTICE: socket 0 mp config
NOTICE: Gicd, its and mbigen dreset ok
NOTICE: Sata dreset ok
NOTICE: Aic dreset ok, state 0x0
NOTICE: Peri sub mbigen init ok
NOTICE: L3D sec space cfg...NOTICE: ok
NOTICE: L3t lp icg module en cfg...NOTICE: ok
NOTICE: MN init(ASIC/EMU) start
NOTICE: MN barrier 0x35b, dvm 0x31b
NOTICE: MN init ok
NOTICE: NIC/SATA/USB SMMU bypass ok
NOTICE: Smmu init(ASIC/EMU) ok
NOTICE: L2buf secure init ok
NOTICE: ErrRsp Config(ASIC/EMU) ok
NOTICE: switch 1.8V voltage for sd is ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTINOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: mApeiTrustfirmwareStruc = 0x10602000
NOTICE: BL3-1: clean atf dcache
NOTICE: BL3-1: jump to prepi entry
current keypoint[71], last keypoint[0].
[1.107] [BOOT_TRACE] auto boot.
This is sd boot entry
emmcsd init
count(1)
end
SYS Enable:0x0, gpio:0x5
recEnable:0x0, gpioStatus:0x0
current keypoint[89], last keypoint[0].
start load os image
try flag:0x0, reset count:0x0
cpld val: 0x0.
boot2 reset count:0x1
Current start mode :0x0 not support.
boot area main.
1301 imgS.
5173 imgE.
[5.305] [BOOT_TRACE] load image success.
load crl from Storage media
current keypoint[90], last keypoint[0].
waiting for hsm ready..OK
[5.334] [BOOT_TRACE] Tee Load Start.
ERROR: image size check fail!
ERROR: size check failed!
ERROR: tee check before verity fail!
ERROR: tee decrypt or cms verify failed.
Image Auth Fail, 0xFFFFFFFF!
TEE Verify Fail, Size = 0x500000, status = 0xFFFFFFFF!
TEE Load Failed, Status = Security Violation!
Normal boot fail, Status = Security Violation. start to b .