ep/rc mode: 0

Enable wdg.

#1

Pll Init ..pll[0] inited

pll[2] inited

pll[3] inited

pll[4] inited

pll[5] inited

OK.

reset src:0x000003b6

lsadc dreset ok

lsadc0 init ok

adc0in0:92 adc0in1:588 adc0in2:224

adc1in2:4 adc1in3:91

adc boardId:10251

Load slave hboot1_a

Load slave hilink25

hboot1a hash 6277dd7a.

Boot Entry.

Load slave hboot1_b

[0.090] [BOOT_TRACE]1b start

current[3], last[71]

Dfx init l2 xloader done

Hboot1_a point:[06] 01 02 05 06 11 15 00 00 00 00 00 00 00 00 00 00 00 00 00 00

sfc set Qline.

Device id: 0x3925c2

Flash unsport Quad.

Boot entry(121)

Iso state: 0x0

pll[6] inited

pll[7] inited

pll[8] inited

pll[9] inited

pll[10] inited

Board info:

sctrl pad info:0xd08c0

boardid:10251

bootmode:3

rc/ep mode:0

pg info:0

reset reason:0x3b6

sfc mode:4byte

secure boot:1

current[4], last[71]

[0.143] [BOOT_TRACE]Load slave userbasecfg

non-secure vef success!

invalid strategy offset 1.

Cfg type-1 no cfg info.

No info in userBaseConfig

current[5], last[71]

[0.158] [BOOT_TRACE]Load slave sysbasecfg

SyscfgProc [345|0|1]

Select a power level based on the low power consumption configuration.!

Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33

bitmap info update load success

SyscfgProc [347|0|1]

write share info ok

write nosec share info ok

current[6], last[71]

[0.203] [BOOT_TRACE]Load slave lpddr

[0.261] [BOOT_TRACE]Dreset Ts OK

current[7], last[71]

[0.261] [BOOT_TRACE]Load slave hsmtag

current[8], last[71]

[0.319] [BOOT_TRACE]Load slave atf

report atf info to ddr OK

current[9], last[71]

[0.393] [BOOT_TRACE]Load slave hboot2

report uefi info to ddr OK

PCIE0/1/2/3 RC Config Preset OK.

use macro setting from syscfg

macro[0] protocols:

ds[0] : PCIE

ds[1] : PCIE

ds[2] : PCIE

ds[3] : PCIE

macro[1] protocols:

ds[0] : USB

ds[1] : USB

ds[2] : USB

ds[3] : USB

6Macro[0] power up (time 807ms)

iecc disable

Rpt 0x2000, fb 0x800, msdw 0x2000

[0.533] [BOOT_TRACE] ddr init end

Macro[1] power up (time 860ms)

cp_area_l2buf_2_ddr

Dfx init ddr done

Backup bbox data

Copy cfg OK.

Copy cfg OK.

Copy ddr Cache done.

current[10], last[71]

[0.921] [BOOT_TRACE]finish image load.

current[20], last[71]

current[70], last[71]

[928.928]Dreset main core...

Jump to HSM...

NOTICE: Mp conf...NOTICE: ok

NOTICE: Booting Trusted Firmware

NOTICE: BL1:

NOTICE: BL1: Built :

NOTICE: BL1: Booting BL2

NOTICE: BL2:

NOTICE: BL2: Built :

NOTICE: BL1: Booting BL31

NOTICE: BL31:

NOTICE: BL31: Built :

NOTICE: HSM boot keypoint 0x7807f!

NOTICE: A55 wfi ...NOTICE: OK

NOTICE: A55 close

NOTICE: jumper to uefi [1035]

current keypoint[71], last keypoint[71].

macmode:0x1, ulPort:0x0, ulPhyID:0x1CC910, ulMacSpeed:0x2!

The default boot selection will start in 1 seconds

[1.866] [BOOT_TRACE] auto boot.

This is SSD boot entry

Locate handle buffer error, handle num is 0, Status = Not Found

Normal boot fail, Status = Not Found. start to b .