烧录官方最新镜像opiaipro_ubuntu22.04_desktop_aarch64_20250925.img.xz到SD卡后无法开机，又换用各种工具(Win32DiskImager, BalendEtcher, 昇腾开发者套件一键制卡工具，Rasperberry Imager)并尝试在Windows/Linux两个环境中重新烧录其他镜像opiaipro_ubuntu22.04_desktop_aarch64_20241128.img.xz opiaipro_ubuntu22.04_minimal_aarch64_20250925.img.xz等进行尝试，发现都无法正常开机，使用串口终端发现在经过多次自动重启最终在Jumper to uefi处卡住了，拨码已经全部拨到右侧(从SD卡启动)，串口日志如下:
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:93 adc0in1:588 adc0in2:224
adc1in2:2 adc1in3:95
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 13
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.142] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.157] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.202] [BOOT_TRACE]Load main lpddr
[0.260] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.260] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.318] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.392] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
CMacro[0] power up (time 806ms)
disable
Rpt 0x4000, fb 0x1000, msdw 0x4000
[0.788] [BOOT_TRACE] ddr init end
Macro[1] power up (time 858ms)
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.988] [BOOT_TRACE]finish image load.
current[20], last[0]
current[70], last[0]
[995.995]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1101]
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:93 adc0in1:588 adc0in2:225
adc1in2:1 adc1in3:92
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 13
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.143] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.158] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.203] [BOOT_TRACE]Load main lpddr
[0.261] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.261] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.319] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.393] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
6Macro[0] power up (time 807ms)
ap: 0x33
ddr freq: 1596
iecc disable
Rpt 0x4000, fb 0x1000, msdw 0x4000
[0.792] [BOOT_TRACE] ddr init end
Macro[1] power up (time 860ms)
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.989] [BOOT_TRACE]finish image load.
current[20], last[0]
current[70], last[0]
[997.997]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1103]
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:96 adc0in1:587 adc0in2:223
adc1in2:1 adc1in3:92
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 13
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.143] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.158] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.203] [BOOT_TRACE]Load main lpddr
[0.261] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.261] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.319] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.393] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
dMacro[0] power up (time 807ms)
0x4000, fb 0x1000, msdw 0x4000
[0.786] [BOOT_TRACE] ddr init end
Macro[1] power up (time 859ms)
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.989] [BOOT_TRACE]finish image load.
current[20], last[0]
current[70], last[0]
[996.996]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1102]
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x0000000b
lsadc dreset ok
lsadc0 init ok
adc0in0:93 adc0in1:586 adc0in2:224
adc1in2:0 adc1in3:91
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[70]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 00 00 00 00 00 00 00 00 00 00 0
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(121)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0xb
sfc mode:4byte
secure boot:1
current[4], last[70]
[0.143] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[70]
[0.157] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[70]
[0.202] [BOOT_TRACE]Load main lpddr
[0.260] [BOOT_TRACE]Dreset Ts OK
current[7], last[70]
[0.261] [BOOT_TRACE]Load main hsmtag
current[8], last[70]
[0.319] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[70]
[0.393] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
Macro[0] power up (time 807ms)
x33
ddr freq: 1596
iecc disable
Rpt 0x4000, fb 0x1000, msdw 0x4000
[0.791] [BOOT_TRACE] ddr init end
Macro[1] power up (time 859ms)
cp_area_l2buf_2_ddr
Dfx init ddr done
Backup bbox data
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[70]
[0.930] [BOOT_TRACE]finish image load.
current[20], last[70]
current[70], last[70]
[938.938]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1044]
点赞
收藏
回复
分享
举报
已解决
烧录官方最新镜像opiaipro_ubuntu22.04_desktop_aarch64_20250925.img.xz到SD卡后无法开机，又换用各种工具(Win32DiskImager, BalendEtcher, 昇腾开发者套件一键制卡工具，Rasperberry Imager)并尝试在Windows/Linux两个环境中重新烧录其他镜像opiaipro_ubuntu22.04_desktop_aarch64_20241128.img.xz opiaipro_ubuntu22.04_minimal_aarch64_20250925.img.xz等进行尝试，发现都无法正常开机，使用串口终端发现在经过多次自动重启最终在Jumper to uefi处卡住了，拨码已经全部拨到右侧(从SD卡启动)，串口日志如下:
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:93 adc0in1:588 adc0in2:224
adc1in2:2 adc1in3:95
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 13
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.142] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.157] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.202] [BOOT_TRACE]Load main lpddr
[0.260] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.260] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.318] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.392] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
CMacro[0] power up (time 806ms)
disable
Rpt 0x4000, fb 0x1000, msdw 0x4000
[0.788] [BOOT_TRACE] ddr init end
Macro[1] power up (time 858ms)
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.988] [BOOT_TRACE]finish image load.
current[20], last[0]
current[70], last[0]
[995.995]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1101]
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:93 adc0in1:588 adc0in2:225
adc1in2:1 adc1in3:92
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 13
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.143] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.158] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.203] [BOOT_TRACE]Load main lpddr
[0.261] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.261] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.319] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.393] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
6Macro[0] power up (time 807ms)
ap: 0x33
ddr freq: 1596
iecc disable
Rpt 0x4000, fb 0x1000, msdw 0x4000
[0.792] [BOOT_TRACE] ddr init end
Macro[1] power up (time 860ms)
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.989] [BOOT_TRACE]finish image load.
current[20], last[0]
current[70], last[0]
[997.997]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1103]
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x00000001
lsadc dreset ok
lsadc0 init ok
adc0in0:96 adc0in1:587 adc0in2:223
adc1in2:1 adc1in3:92
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[0]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 21 65 28 95 198 11 00 128 209 13
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(120)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0x1
sfc mode:4byte
secure boot:1
current[4], last[0]
[0.143] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[0]
[0.158] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[0]
[0.203] [BOOT_TRACE]Load main lpddr
[0.261] [BOOT_TRACE]Dreset Ts OK
current[7], last[0]
[0.261] [BOOT_TRACE]Load main hsmtag
current[8], last[0]
[0.319] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[0]
[0.393] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
dMacro[0] power up (time 807ms)
0x4000, fb 0x1000, msdw 0x4000
[0.786] [BOOT_TRACE] ddr init end
Macro[1] power up (time 859ms)
Dfx init ddr done
Init bbox data region
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[0]
[0.989] [BOOT_TRACE]finish image load.
current[20], last[0]
current[70], last[0]
[996.996]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1102]
ep/rc mode: 0
Enable wdg.
#1
Pll Init ..pll[0] inited
pll[2] inited
pll[3] inited
pll[4] inited
pll[5] inited
OK.
reset src:0x0000000b
lsadc dreset ok
lsadc0 init ok
adc0in0:93 adc0in1:586 adc0in2:224
adc1in2:0 adc1in3:91
adc boardId:10251
Load main hboot1_a
Load main hilink25
hboot1a hash 6277dd7a.
Boot Entry.
Load main hboot1_b
[0.090] [BOOT_TRACE]1b start
current[3], last[70]
Dfx init l2 xloader done
Hboot1_a point:[06] 01 02 05 06 11 15 00 00 00 00 00 00 00 00 00 00 0
sfc set Qline.
Device id: 0x3925c2
Flash unsport Quad.
Boot entry(121)
Iso state: 0x0
pll[6] inited
pll[7] inited
pll[8] inited
pll[9] inited
pll[10] inited
Board info:
sctrl pad info:0xd0940
boardid:10251
bootmode:5
rc/ep mode:0
pg info:0
reset reason:0xb
sfc mode:4byte
secure boot:1
current[4], last[70]
[0.143] [BOOT_TRACE]Load main userbasecfg
non-secure vef success!
invalid strategy offset 1.
Cfg type-1 no cfg info.
No info in userBaseConfig
current[5], last[70]
[0.157] [BOOT_TRACE]Load main sysbasecfg
SyscfgProc [345|0|1]
Select a power level based on the low power consumption configuration.!
Update bitmap: 0xf 0x1 0x1 0x0 0x3 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x1 0x5 0x5 0x33
bitmap info update load success
SyscfgProc [347|0|1]
write share info ok
write nosec share info ok
current[6], last[70]
[0.202] [BOOT_TRACE]Load main lpddr
[0.260] [BOOT_TRACE]Dreset Ts OK
current[7], last[70]
[0.261] [BOOT_TRACE]Load main hsmtag
current[8], last[70]
[0.319] [BOOT_TRACE]Load main atf
report atf info to ddr OK
current[9], last[70]
[0.393] [BOOT_TRACE]Load main hboot2
report uefi info to ddr OK
PCIE0/1/2/3 RC Config Preset OK.
use macro setting from syscfg
macro[0] protocols:
ds[0] : PCIE
ds[1] : PCIE
ds[2] : PCIE
ds[3] : PCIE
macro[1] protocols:
ds[0] : USB
ds[1] : USB
ds[2] : USB
ds[3] : USB
Macro[0] power up (time 807ms)
x33
ddr freq: 1596
iecc disable
Rpt 0x4000, fb 0x1000, msdw 0x4000
[0.791] [BOOT_TRACE] ddr init end
Macro[1] power up (time 859ms)
cp_area_l2buf_2_ddr
Dfx init ddr done
Backup bbox data
Copy cfg OK.
Copy cfg OK.
Copy ddr Cache done.
current[10], last[70]
[0.930] [BOOT_TRACE]finish image load.
current[20], last[70]
current[70], last[70]
[938.938]Dreset main core...
Jump to HSM...
NOTICE: Mp conf...NOTICE: ok
NOTICE: Booting Trusted Firmware
NOTICE: BL1:
NOTICE: BL1: Built :
NOTICE: BL1: Booting BL2
NOTICE: BL2:
NOTICE: BL2: Built :
NOTICE: BL1: Booting BL31
NOTICE: BL31:
NOTICE: BL31: Built :
NOTICE: HSM boot keypoint 0x7807f!
NOTICE: A55 wfi ...NOTICE: OK
NOTICE: A55 close
NOTICE: jumper to uefi [1044]